China best Theme Park Open Type Childern Rail Train 120 Seats Powered by Diesel near me shop

Product Description

1.Feature and advantage:

Theme Park  Mini Track Train/ Locomotive with 120 Seats  

Manufacturer for Amusement Rides Mini Diesel  Track Train with High quality & conpetitive price you. Customer is welcome to visit our new showroom and factory located in HangZhou City, China. 

2.Specifications

DST01-7C-120B Open-type Sightseeing Mini Train

Gauge: 762/900/1435mm
Marshalling:  locomotive +coal water truck  + carriage*3
Speed: 10km/h
Crew: 40 *3=120
Mat limit slope: 30 per thousand
Restriction curve radius: 30m 
Power: diesel generating set (Cummins) 

2.1 Ambient conditions and vehicle parameters

1) Project location height is not more than 2000 meters above sea level.
2) The air temperature is between -10 and 40 degree.
3) Electronic components must not be activated without dehumidification in relative humidity greater than 95% or condensation.
4) Vehicles should be CZPT to withstand the invasion of wind and sand and the resistance to salt spray
5) Line gauge: 762mm
6) Limiting slope: 30 ‰ (reduction calculations for curves)
7) The radius of the line longitudinal curve is 200m
8) Line minimum curve radius 40m, difficult area 30m
   

              
2.2 Vehicle parameters

1) Style: European classical (see attachment renderings)
2) Gauge: 762mm
3) Formation mode: locomotive + coal water truck + compartment + compartment + compartment + compartment
4) Group size 38.2m (length) x 1.9m (width) x 2.8m (height)
5) Passenger Capacity: 128 seats
6) Limit curve radius: 40m, difficult section (station) 30m
7) Limit slope: <= 30‰, curve section needs to perform this calculation
8) Speed: 0-10km/H
9) Emergency braking distance: <4m
10) Xihu (West Lake) Dis.d tour system: The host is located on the bridge of the locomotive, the audio is located in each compartment, playing background music, site broadcast, temporary voice notification
11) Overall dimensions mm: 10170 (length) * 2000 (width) * 2830 (high)
12) Driver’s seat: seated 2 seats
13) Structure: Q235 profile, steel plate welding
14) Locomotive axis sequence: 2-2-0
15) Drive system:
16) Coal Waterwheels: Power Bogies
17) Drive Motor : 7.5KW*4 Variable Frequency Motor
18) Speed control method: frequency conversion speed control touch screen + plc + inverter S curve acceleration vector control 19) Main power source: CZPT diesel generator set 80kw, Stanford generator
20) Braking system: Working brake: Regenerative braking (motor fed brake) Emergency, parking brake: Electropneumatic braking
21) Forward driving video (improving driver’s view)
22) EffectSmokestack effect of continuous smoke \steam whistle\copper bell (12 inches)
23) Overall dimensions mm: 6.2 (L) * 1900 (W) * 2800 (H)
24) Cabin form: semi-open type, on both sides of the car, with car steps
25) Minimum height of passenger area: 1800mm
26) Floor height: 600mm (rail surface)
27) Step height: 400mm (rail surface)
28) Structure: Q235 profile, sheet metal welding, roof FRP composite
29) Running system: Bogie form (with automatic emergency braking)
30) Renovation: Roof interior wallsolid wood buckle + wood paint (6 degrees) Floor: bamboo plastic plate + pattern aluminum
31)Seats: 32 seats (wooden seats) Lamps: Antique LED Ceiling Lights Sound: Wood Effect Ceiling Speakers
32)Car side railing: solid wood (weathering wood oil 6 degrees)
33)Side door: 8 sided, FRP CZPT (inside solid wood) End window: Solid wood pHangZhou window
34)Urveillance: Camera (recording) 2pcs/car
35) European metal corner flower on the roof: 16 handrails on and off: 304 stainless steel
36)Weather curtain: transparent shutter (removable, fast retractable)

2.3 Company profile

HangZhou dising technologies Co., Ltd.Is located in the east lake new technology development zone in HangZhou, ZheJiang province.It is a professional supplier of tourist attraction, theme park, characteristic town, and commercial block slow rail transit system;Our service covers the whole process of slow rail transit system survey and design, special track vehicle design and so on.
We promise to improve our professional skills and be based on a careful design attitude, a profound understanding of customer needs and a rich experience in project implementation, to provide customers with high quality and reliable products and economic and reasonable projects.

2.4 Products Series

In the years of industry experience, the company created the ZheJiang tenyun steam locomotive replica plate, the Tianya  corner scenic spot in ZheJiang , the HangZhou Yuet square project, the tram, the ZheJiang lling National Agricultural Park sightseeing train, the Xihu (West Lake) Dis. Lu Jia Village sightseeing small train and so on. The main products covers 3 kinds of landscapes:tourism. Sightseeing trains, sightseeing trams and locomotives 3 kinds of landscapes.

1. Electric Train Sets
2. Electric Locomotive
3. Fun Train
4. Sightseeing Mini Train
5. Tram

5. Delivery and Shipment

Shipping by sea: Around 4 weeks to arrive.
Delivery Time: Around 30 working days after receipt of deposit.
MOQ: 1 set.
Payment Term:  30% T/T deposit, 70% T/T before delivery.

6. Warranty and post service 

Mini Electric Trackless Train for Tourist: 1 year full warranty,offer FREE components under EXW shipped term.
oversea engineer aftre sale service available

7. FAQ

Q1. What is your terms of packing?

A: Generally, we pack our goods in neutral white boxes and brown cartons. If you have legally registered patent, we can pack the goods in your branded boxes after getting your authorization letters.

Q2. What is your terms of payment?

A: T/T 30% as deposit, and 70% before delivery. We’ll show you the photos of the products and packages before you pay the balance.

Q3. What is your terms of delivery?

A: EXW, FOB, CFR, CIF, DDU.

Q4. How about your delivery time?

A: Generally, it will take 30 to 60 days after receiving your advance payment. The specific delivery time depends on the items and the quantity of your order.

Q5. Can you produce according to the samples?

A: Yes, we can produce by your samples or technical drawings. We can build the molds and fixtures.

Q6. What is your sample policy?

A: We can supply the sample if we have ready parts in stock, but the customers have to pay the sample cost and the courier cost.

Q7. Do you test all your goods before delivery?

A: Yes, we have 100% test before delivery

Q8: How do you make our business long-term and good relationship?

A:1. We keep good quality and competitive price to ensure our customers benefit ;

2. We respect every customer as our friend and we sincerely do business and make friends with them, no matter where they come from.

Screw Shaft Features Explained

When choosing the screw shaft for your application, you should consider the features of the screws: threads, lead, pitch, helix angle, and more. You may be wondering what these features mean and how they affect the screw’s performance. This article explains the differences between these factors. The following are the features that affect the performance of screws and their properties. You can use these to make an informed decision and purchase the right screw. You can learn more about these features by reading the following articles.

Threads

The major diameter of a screw thread is the larger of the 2 extreme diameters. The major diameter of a screw is also known as the outside diameter. This dimension can’t be directly measured, but can be determined by measuring the distance between adjacent sides of the thread. In addition, the mean area of a screw thread is known as the pitch. The diameter of the thread and pitch line are directly proportional to the overall size of the screw.
The threads are classified by the diameter and pitch. The major diameter of a screw shaft has the largest number of threads; the smaller diameter is called the minor diameter. The thread angle, also known as the helix angle, is measured perpendicular to the axis of the screw. The major diameter is the largest part of the screw; the minor diameter is the lower end of the screw. The thread angle is the half distance between the major and minor diameters. The minor diameter is the outer surface of the screw, while the top surface corresponds to the major diameter.
The pitch is measured at the crest of a thread. In other words, a 16-pitch thread has a diameter of 1 sixteenth of the screw shaft’s diameter. The actual diameter is 0.03125 inches. Moreover, a large number of manufacturers use this measurement to determine the thread pitch. The pitch diameter is a critical factor in successful mating of male and female threads. So, when determining the pitch diameter, you need to check the thread pitch plate of a screw.
screwshaft

Lead

In screw shaft applications, a solid, corrosion-resistant material is an important requirement. Lead screws are a robust choice, which ensure shaft direction accuracy. This material is widely used in lathes and measuring instruments. They have black oxide coatings and are suited for environments where rusting is not acceptable. These screws are also relatively inexpensive. Here are some advantages of lead screws. They are highly durable, cost-effective, and offer high reliability.
A lead screw system may have multiple starts, or threads that run parallel to each other. The lead is the distance the nut travels along the shaft during a single revolution. The smaller the lead, the tighter the thread. The lead can also be expressed as the pitch, which is the distance between adjacent thread crests or troughs. A lead screw has a smaller pitch than a nut, and the smaller the lead, the greater its linear speed.
When choosing lead screws, the critical speed is the maximum number of revolutions per minute. This is determined by the minor diameter of the shaft and its length. The critical speed should never be exceeded or the lead will become distorted or cracked. The recommended operational speed is around 80 percent of the evaluated critical speed. Moreover, the lead screw must be properly aligned to avoid excessive vibrations. In addition, the screw pitch must be within the design tolerance of the shaft.

Pitch

The pitch of a screw shaft can be viewed as the distance between the crest of a thread and the surface where the threads meet. In mathematics, the pitch is equivalent to the length of 1 wavelength. The pitch of a screw shaft also relates to the diameter of the threads. In the following, the pitch of a screw is explained. It is important to note that the pitch of a screw is not a metric measurement. In the following, we will define the 2 terms and discuss how they relate to 1 another.
A screw’s pitch is not the same in all countries. The United Kingdom, Canada, and the United States have standardized screw threads according to the UN system. Therefore, there is a need to specify the pitch of a screw shaft when a screw is being manufactured. The standardization of pitch and diameter has also reduced the cost of screw manufacturing. Nevertheless, screw threads are still expensive. The United Kingdom, Canada, and the United States have introduced a system for the calculation of screw pitch.
The pitch of a lead screw is the same as that of a lead screw. The diameter is 0.25 inches and the circumference is 0.79 inches. When calculating the mechanical advantage of a screw, divide the diameter by its pitch. The larger the pitch, the more threads the screw has, increasing its critical speed and stiffness. The pitch of a screw shaft is also proportional to the number of starts in the shaft.

Helix angle

The helix angle of a screw shaft is the angle formed between the circumference of the cylinder and its helix. Both of these angles must be equal to 90 degrees. The larger the lead angle, the smaller the helix angle. Some reference materials refer to angle B as the helix angle. However, the actual angle is derived from calculating the screw geometry. Read on for more information. Listed below are some of the differences between helix angles and lead angles.
High helix screws have a long lead. This length reduces the number of effective turns of the screw. Because of this, fine pitch screws are usually used for small movements. A typical example is a 16-mm x 5-inch screw. Another example of a fine pitch screw is a 12x2mm screw. It is used for small moves. This type of screw has a lower lead angle than a high-helix screw.
A screw’s helix angle refers to the relative angle of the flight of the helix to the plane of the screw axis. While screw helix angles are not often altered from the standard square pitch, they can have an effect on processing. Changing the helix angle is more common in two-stage screws, special mixing screws, and metering screws. When a screw is designed for this function, it should be able to handle the materials it is made of.
screwshaft

Size

The diameter of a screw is its diameter, measured from the head to the shaft. Screw diameters are standardized by the American Society of Mechanical Engineers. The diameters of screws range from 3/50 inches to 16 inches, and more recently, fractions of an inch have been added. However, shaft diameters may vary depending on the job, so it is important to know the right size for the job. The size chart below shows the common sizes for screws.
Screws are generally referred to by their gauge, which is the major diameter. Screws with a major diameter less than a quarter of an inch are usually labeled as #0 to #14 and larger screws are labeled as sizes in fractions of an inch. There are also decimal equivalents of each screw size. These measurements will help you choose the correct size for your project. The screws with the smaller diameters were not tested.
In the previous section, we described the different shaft sizes and their specifications. These screw sizes are usually indicated by fractions of an inch, followed by a number of threads per inch. For example, a ten-inch screw has a shaft size of 2” with a thread pitch of 1/4″, and it has a diameter of 2 inches. This screw is welded to a two-inch Sch. 40 pipe. Alternatively, it can be welded to a 9-inch O.A.L. pipe.
screwshaft

Shape

Screws come in a wide variety of sizes and shapes, from the size of a quarter to the diameter of a U.S. quarter. Screws’ main function is to hold objects together and to translate torque into linear force. The shape of a screw shaft, if it is round, is the primary characteristic used to define its use. The following chart shows how the screw shaft differs from a quarter:
The shape of a screw shaft is determined by 2 features: its major diameter, or distance from the outer edge of the thread on 1 side to the inner smooth surface of the shaft. These are generally 2 to 16 millimeters in diameter. Screw shafts can have either a fully threaded shank or a half-threaded shank, with the latter providing better stability. Regardless of whether the screw shaft is round or domed, it is important to understand the different characteristics of a screw before attempting to install it into a project.
The screw shaft’s diameter is also important to its application. The ball circle diameter refers to the distance between the center of 2 opposite balls in contact with the grooves. The root diameter, on the other hand, refers to the distance between the bottommost grooves of the screw shaft. These are the 2 main measurements that define the screw’s overall size. Pitch and nominal diameter are important measurements for a screw’s performance in a particular application.

Lubrication

In most cases, lubrication of a screw shaft is accomplished with grease. Grease is made up of mineral or synthetic oil, thickening agent, and additives. The thickening agent can be a variety of different substances, including lithium, bentonite, aluminum, and barium complexes. A common classification for lubricating grease is NLGI Grade. While this may not be necessary when specifying the type of grease to use for a particular application, it is a useful qualitative measure.
When selecting a lubricant for a screw shaft, the operating temperature and the speed of the shaft determine the type of oil to use. Too much oil can result in heat buildup, while too little can lead to excessive wear and friction. The proper lubrication of a screw shaft directly affects the temperature rise of a ball screw, and the life of the assembly. To ensure the proper lubrication, follow the guidelines below.
Ideally, a low lubrication level is appropriate for medium-sized feed stuff factories. High lubrication level is appropriate for larger feed stuff factories. However, in low-speed applications, the lubrication level should be sufficiently high to ensure that the screws run freely. This is the only way to reduce friction and ensure the longest life possible. Lubrication of screw shafts is an important consideration for any screw.

China best Theme Park Open Type Childern Rail Train 120 Seats Powered by Diesel   near me shop China best Theme Park Open Type Childern Rail Train 120 Seats Powered by Diesel   near me shop