China Good quality PE150X250 Diesel Engine Drive Jaw Crusher CZPT Rock Cone Hammer Impact Sand Making Machine with Free Design Custom

Product Description

PE150X250 Diesel Engine Drive Jaw Crusher

1. D1525 details
Shanman Model D1525 jaw crusher powered by diesel engine, feeding size is 150 mm, output size is 10-40 mm, the final aggregate size is 1 type, such as 0-20mm, capacity is 1-3t/h. It’s is widely used for crushing various materials like stone, granite, trap rock, coke, coal, manganese ore, iron ore, emery, fused aluminum, oxide, fused calcium carbide, lime stone, quartz, alloys, etc,is a Single Toggle Roller Bearing machine.

2. D1525 jaw crusher pictures show

3. Jaw crusher introduction
Jaw Crusher is ideally suitable as primary and secondary crusher for material with compression strength less than 320Mpa. Jaw crusher is widely used for crushing various materials like stone, granite, trap rock, coke, coal, manganese ore, iron ore, emery, fused aluminum, oxide, fused calcium carbide, lime stone, quartzite, alloys, etc,is a Single Toggle Roller Bearing machine.

Item Spcification
Max Feeding size  150mm
Feeding size 150x250mm
Capacity 1-3t/h
Weight  1.2t
Engine Power  8hp
Overall dimension 1400x1050x1450mm
Adjustment Range 10-40mm
Machine includes jaw crusher,diesel engine,shelf
Power supply Engine
Final aggregate size 0-20mm(changable)

4. Jaw crusher working principle:
The diesel engine drives the eccentric shaft of the jaw crusher through the triangular belt and the trough wheel to make the jaw crusher move reciprocally, so as to crush the material entering the crushing chamber. These final aggregates size can be changed according to clients request, such as 0-10mm, or 0-20mm, or 0-40mm, different final size will be different capacity.

5. Usage
The machine is simple in structure, reliable in work, easy to use and maintain, mainly used in mining, quarry building materials and other departments where electricity is inconvenient, coarse and medium crushing various kinds of ores or rocks with strength below 250Mpa.

6. Jaw crusher features

  1. Diesel engine power, no need electric.
  2. You can use it directly after put into diesel. Easy operation.
  3. Simple structure, easy maintenance
  4. High crushing ratio, even output granularity
  5. High reliability, low investment
  6. Low noise, less dust.
  7. Jaw crusher have flexible capacity, you can adjust the output size from 10mm to 40mm to meet your own final aggregates size requirements.

7. Jaw crusher specifications

Model Max Feeding (mm) Adjustment Range(mm) Capacity (t/h) Motor Power            (kw) Overall Dimension    (mm)
PE150*250 150 10-40 1-3 Y180L-6(5.5) 875*745*935
PE250*400 210 20-80 8-35 Y180L-6(15kw) 1198*1274*1295
PE400*600 340 40-100 15-80 Y250M-8(30kw) 1866*1748*1600
PE500*750 425 50-120 20-100 Y280M-8(55kw) 1905*1950*2034
PE600*900 520 62-200 50-180 Y315S-6(75kw) 2540*2056*2365
PE750*1060 630 100-280 100-350 Y315L2-6(132kw) 3250*2480*2930
PE900*1200 750 100-300 250-600 Y2-355M1-6(160kw) 3900*2890*3410
PE1200*1500 1571 150-400 500-1000 Y2-355L-6 (250kw) 4100*3200*4200
PEX250*1000 210 20-80 15-50 Y225M-6(30kw) 1400*1915*1490
PEX250*1200 210 25-90 20-70 Y250M-6(37kw) 1400*2115*1490
PEX300*1300 250 30-100 30-100 Y280M-6(55kw) 1770*2420*1550
Note: If there is any modification, all parameters are subject to the machine.

9.Customer visit

10. Certifications:

11. Shanman service

  1. Assist clients to choose the suitable machine
  2. Design and manufacture machines according to customer’s special requirements
  3. The company is free of charge to the user on-site engineering and technical personnel plHangZhou site for the user to design the best processes and program
  4. Arrange for visiting our factory, assist them to handle relative procedure, such as visa.
  5. Make sure goods prepared within delivery time;
  6.  Pre-check and accept products ahead of delivery;
  7. Prepare documents required to help customer pass customs clearance.
  8. Help clients to make Project evaluation and feasibility analysis and draft solving plans.
  9. Provide technical engineers to CZPT the installation;
  10. Train clients worker how to operate;
  11. Offer spare parts at a best price for long term.

12. Packing & shipping

13.Questions you may have

Q: Are you mining machinery manufacturer?
A: Yes, we are manufacturer, we warmly welcome clients to visit our factory at anytime. We can also provide samples test, mine design, equipment manufacture, after-sale service, etc…

Q: how to choose the suitable machine?
A: To design a suitable machine, please let me know the following information:

  1. what kind of CZPT do you want to crush ? like limestone ? or granite ?
  2. what’s the size of your CZPT before crush ? how many inch or mm ? 
  3. how big capacity do you need?2t/h?10t/h?100t/h?
  4. what’s your requirements of final product size ? how many inches or mm ?0-5mm?5-20mm? Or others?
  5. you only need 1 set of crusher or a whole crushing line? (Include the feeder ,crusher, screen, conveyor and so on)
  6. You need mobile crushing machine or stationary one?

Q: How long is the warranty of your machine? Does your company supply the spare parts?A: the warranty period is 1 year. we will supply the spare parts for you any time.

Q: If I buy a complete mineral processing line, can you help us to build it?
A: Yes, we can help you combine a complete mineral processing line and give you related professional advice. We had already build many mining projects in China & Overseas.

Q: how about the installation?

A: Supplier provides a full set of installation drawings and instructions. If the buyer need supplier do the installation, supplier will provide technical engineers to CZPT the installation, and train buyer’ workers. Buyer should take the charges for technicians and pay them salary. 

 
Q: what is the payment Method?
A: By T/T, L/C,  Western Union, Money Gram, and so on. 

14. Small  series crusher

15. About us
Shanman Machinery Crusher Production Base is a company specializing in the production of jaw crushers, impact crushers, cone crushers, sand making machines, vibrating feeders, vibrating screens, mobile CZPT crushers and other crushing and screening machines. The company was founded in 2571, covers an area of 20,000 square meters, has more than 100 employees, 5 chief engineers and more than 10 after-sales service personnel, these can ensure your solution. Shanman has now become a production and export base for the crushing and screening industry.
As a production plant, we can produce crushing and screening machines according to your actual needs. Many models we develop and produce are designed and produced according to different customer requirements. You can let us know your thoughts, and professional engineers will help you.
Our mission
Carry out independent and innovative research in the design field of crushing and screening equipment and devote to the production of the most suitable equipment.
We are committed to producing high-quality and cheap machinery.
Production of machines for people in need, production of the most suitable machines
Our vision
Establish a first-class production base to inject power into the crushing and screening industry
Join hands with Shanman to create a better future.

Address: Xihu (West Lake) Dis. District, HangZhou City, ZheJiang Province, China
 

When your axle needs to be replaced

If you’re wondering when your axle needs to be replaced, you should be aware of these signs first. A damaged axle is usually a sign that your car is out of balance. To tell if the axle needs to be replaced, listen for the strange noise the wheels make as they move. A rhythmic popping sound when you hit bumps or turns indicates that your axle needs to be replaced. If this sounds familiar, you should visit a mechanic.
Driveshaft

Symptoms of a broken shaft

You may notice a clicking or clanking sound from the rear of the vehicle. The vibrations you feel while driving may also indicate damaged axles. In severe cases, your car may lose control, resulting in a crash. If you experience these symptoms, it’s time to visit your auto repair shop. For just a few hundred dollars, you can get your car back on the road, and you don’t have to worry about driving.
Often, damaged axles can be caused by a variety of causes, including poor shock or load bearing bearings. Other causes of axle problems can be an overloaded vehicle, potholes, or a car accident. A bad axle can also cause vibrations and power transmission failures while driving. A damaged axle can also be the result of hitting a curb or pothole. When shaft damage is the cause of these symptoms, it must be repaired immediately.
If your car’s front axle is bent, you may need to replace them at the same time. In this case, you need to remove all tires from the car, separate the driveshaft from the transmission, and remove the axle. Be sure to double check the alignment to make sure everything is ok. Your insurance may cover the cost of repairs, but you may need to pay a deductible before getting coverage.
Axle damage is a common cause of vehicle instability. Axles are key components of a car that transmit power from the engine to the wheels. If it breaks, your vehicle will not be able to drive without a working axle. Symptoms of damaged axles can include high-speed vibrations or crashes that can shake the entire car. When it breaks down, your vehicle won’t be able to carry the weight of your vehicle, so it’s important to get your car repaired as soon as possible.
When your axle is damaged, the wheels will not turn properly, causing the vehicle to crash. When your car has these problems, the brakes won’t work properly and can make your car unstable. The wheels also won’t line up properly, which can cause the brakes to fail. Also, a damaged axle can cause the brakes to become sluggish and sensitive. In addition to the obvious signs, you can also experience the sound of metal rubbing against metal.

Types of car axles

When you’re shopping for a new or used car, it’s important to know that there are different types of axles. Knowing the year, make, model, trim and body type will help you determine the type you need. For easy purchasing, you can also visit My Auto Shop and fill out the vehicle information checklist. You can also read about drivetrains and braking systems. After mastering the basic information of the vehicle, you can purchase the axle assembly.
There are 2 basic types of automotive axles: short axles and drive axles. The axle is the suspension system of the vehicle. They carry the drive torque of the engine and distribute the weight throughout the vehicle. While short shafts have the advantage of simpler maintenance, dead shafts are more difficult to repair. They’re also less flexible, which means they need to be durable enough to withstand harsh conditions.
Axles can be 1 of 3 basic types, depending on the weight and required force. Semi-floating shafts have a bearing in the sleeve. They attach to the wheel and spin to generate torque. Semi-pontoons are common in light pickup trucks and medium-duty vehicles. They are not as effective as floating axles, but still provide a solid foundation for wheel alignment. To keep the wheels aligned, these axles are an important part of the car.
The front axle is the largest of the 3 and can handle road shocks. It consists of 4 main parts: stub shaft, beam, universal pin and track rod. The front axle is also very important as it helps with steering and handling road shocks. The front axle should be strong and durable, as the front axle is most susceptible to road shocks.
Cars use 2 types of axles: live and dead. Live axles connect to the wheels and drive the vehicle. Dead axles do not drive the wheels and support the vehicle. Those with 2 wheels have live axles. Heavy trucks and trailers use 3 or more. The number of axles varies according to the weight and load of the vehicle. This will affect which type of axle you need.
Driveshaft

life expectancy

There are a few things to keep in mind when determining the life expectancy of an automotive axle. First, you should check for any signs of wear. A common sign is rust. If your vehicle is often driven in snow and ice, you may need to replace the axle. Also, you should listen for strange sounds from the wheels, such as rhythmic thumping.
Depending on the type of axle, your car may have an average lifespan of 70,000 miles. However, if you have an older car, the CV axles probably won’t last 5 years. In this case, you may wish to postpone the inspection. This way, you can save money on repairs. However, the next step is to replace the faulty CV shaft. This process can take anywhere from 1 hour to 3 hours.
Weaker axles will eventually break. If it were weakened, it would compromise the steering suspension, putting other road users at risk. Fortunately, proper maintenance will help extend the life of your axle. Here are some tips for extending its lifespan. A good rule of thumb is to never go over speed bumps. This will cause sudden breakage, possibly resulting in a car accident. To prolong the life of your vehicle’s axles, follow these tips.
Another thing to check is the CV connector. If loose, it can cause vibration or even breakage if not controlled. Loose axles can damage the body, suspension and differential. To make matters worse, the guard on the CV joint could tear prematurely, causing the shaft to come loose. Poor CV connections can damage the differential or transmission if left unchecked. So if you want to maximize the life expectancy of your car’s axles, consider getting them serviced as soon as possible.
Driveshaft

The cost of repairing a damaged axle

A damaged axle may need repair as it is responsible for transferring power from the engine to the wheels. A damaged axle can cause a crash or even loss of control. Repairing an axle is much simpler than dealing with an accident. However, damaged axles can cost hundreds of dollars or more. Therefore, it is important to know what to do if you suspect that your axle may have a damaged component.
When your car needs to be replaced or repaired, you should seek the help of a professional mechanic to keep your car safe. You can save a lot of money by contacting a local mechanic who will provide the parts and labor needed to repair the axle. Also, you can avoid accidents by fixing your car as soon as possible. While axles can be expensive, they can last for many years.
The cost of repairing a damaged axle depends on the amount of repairs required and the vehicle you are driving. Prices range from $300 to $1,000, depending on the car and its age. In most cases, it will cost you less than $200 if you know how to fix a damaged axle. For those without DIY auto repair experience, a new axle can cost as little as $500. A damaged axle is a dangerous part of driving.
Fortunately, there are several affordable ways to repair damaged axles. Choosing a mechanic who specializes in this type of repair is critical. They will assess the damage and decide whether to replace or repair the part. In addition to this, they will also road test your car after completing the repairs. If you are unsure about repair procedures or costs, call a mechanic.

China Good quality PE150X250 Diesel Engine Drive Jaw Crusher CZPT Rock Cone Hammer Impact Sand Making Machine   with Free Design CustomChina Good quality PE150X250 Diesel Engine Drive Jaw Crusher CZPT Rock Cone Hammer Impact Sand Making Machine   with Free Design Custom