Product Description
Product Description
Single Axis Solar Panel Independent Tracking System with Linkage Motor Drive
Single Axis Panel Independent Tracking System with Linkage Motor Drive uses rotary linkage motor drive, double row connected at the same time drive, higher strength, stronger stability. It can track the sunlight in real time and search for light intelligently. Comparing with thetraditional fixed bracket, the power generation can be increased by 10-15%. This system is suitable for multi scene large power station.
Features
1, The traditional square tube girder design has better adaptability.
2, Adopting fishbone purlin, which is better strength, better stability and easy installation.
3, Max. gradient difference adaptability in N-S direction up to 15%.
4, Excellent compatibility with all the mainstream solar modules available in the industry: frame, frameless and bi-facial. Independent 2V module design, which reduces the quantity of piles and the construction cost significantly.
5, Free obstacles among trackers in N-S direction, easy to maintain and clean.
6, Its design is configured with 1 single set of controller, which ensures point-to-point real-time monitoring, easy to detect fault points in time every day and reduce output loss.
7, Reducing the cost and energy consumption comparing with single axis with independent tracking system.
8, Independent design, various land form adaptability.
| Product Advantages |
| Middle rotary drive, 2 measuring belts damping, enhance damping, reduce resonance. |
| Rotary drive system, tracking angle can be reached ±60° |
| The linkage shaft can be adjusted in all directions, and is not affected by high and low staggering. |
| Single motor drive, greatly reduce the cost. |
| System Advantages |
| String power, backup battery, safe and reliable |
| Wireless communication, optimized layout, simple and efficient |
| Intelligent tracking all day to improve power generation |
| Internet cloud data transmission, 5G transmission, real-time monitoring, fast and efficient. |
Product Parameters
| Electrical system parameters | |
| Control mode | MCU |
| Tracking accuracy | 2° |
| Protection level | IP65 |
| Ambient temperature | -40ºC-85ºC |
| Power supply type | AC110-500/DC 300-1500 |
| Monitoring device | Remote monitoring(optional) |
| Communication mode | Wireless / wired communication |
| System basic parameters | |
| Driving form | Rotary device |
| Foundation type | Cement foundation / Steel pile foundation |
| Component type | Single glass panel / double glass panel / frameless panel |
| Tracking range | ± 50 ° |
| Panel layout | Single row vertical/ double row vertical |
| Minimum height above ground | 0.3m(lowest point) |
| System life | More than 30 years |
| Work speed | ≤18m/s |
| Resistance to wind speed | ≤50m/s |
Detailed Photos
Project
Company Profile
ZHangZhoug ChuHangZhou New Energy Co., Ltd, was established in 1999, headquartered in HangZhou city, half an hour from ZheJiang city by speed train. With 22 years of production experience, the quality has been certified by TUV, SGS, ISO 9001 etc. As a leader in the global photovoltaic system industry, the company focuses on the research and development, design, production, engineering installation services and system solutions of support structure products, with application in photovoltaic and construction.
Chuanda‘s main business includes aluminum frame, PV mounting and tracking system, distributed power station development, pipe corridor brackets etc. It is 1 the largest professional manufacturer of PV mounting and tracking system in China and the Asia-Pacific region. ChuHangZhou is committed to providing professional, efficient, and reliable photovoltaic system solutions to global customers. As of 2571, the cumulative global installation of photovoltaic mounting and tracking system has exceeded 15 GW, the cumulative turnover of all the business exceeds 1 billion in RMB.
Workshop
Certifications
Cooperation Partners
FAQ
Q: Are you a manufacturer or a Trading company?
A: We are a leader manufacturer of solar PV mounting systems and related accessories since 1999, with rich practical experience and mature production technology, and has several production lines, and our products have won the favor of customers from all over the world.
Q: What can you get from us?
A: -Professional analysis on the project, supply professional design and drawings from the engineers team
-Big annual capacity of 5GW will guarantee the fast delivery for all the clients
-24H services before selling and after selling from our engineers team and sales team
-High quality control system to guarantee the high quality for every order
-Competitive price from good management on supplier-chain system and high automated equipment
-New products launching every year
-New information from market and industry updating every month
-5 years’ warranty
Q: How to guarantee the quality?
A: – A counter sample will be confirmed and sealed by both sides before bulk production.
-The professional prodution technical instruction is available for all the bulk procedure.
-3 QC steps for every order, including incoming material inspetion, on-site inspection and final inspection.
– Professional testing will be done according to the detailed standard.
Q: Why we are better?
A: – Big production capacity, 2 production base in China.
– Rich production experience, we have 22 years in this industry.
– More than 30 professional engineers for quality control and R&D.
– Competitive price, 5-10% better than the market price, as we have a good raw material supplier chain and quality control system.
Guide to Drive Shafts and U-Joints
If you’re concerned about the performance of your car’s driveshaft, you’re not alone. Many car owners are unaware of the warning signs of a failed driveshaft, but knowing what to look for can help you avoid costly repairs. Here is a brief guide on drive shafts, U-joints and maintenance intervals. Listed below are key points to consider before replacing a vehicle driveshaft.
Symptoms of Driveshaft Failure
Identifying a faulty driveshaft is easy if you’ve ever heard a strange noise from under your car. These sounds are caused by worn U-joints and bearings supporting the drive shaft. When they fail, the drive shafts stop rotating properly, creating a clanking or squeaking sound. When this happens, you may hear noise from the side of the steering wheel or floor.
In addition to noise, a faulty driveshaft can cause your car to swerve in tight corners. It can also lead to suspended bindings that limit overall control. Therefore, you should have these symptoms checked by a mechanic as soon as you notice them. If you notice any of the symptoms above, your next step should be to tow your vehicle to a mechanic. To avoid extra trouble, make sure you’ve taken precautions by checking your car’s oil level.
In addition to these symptoms, you should also look for any noise from the drive shaft. The first thing to look for is the squeak. This was caused by severe damage to the U-joint attached to the drive shaft. In addition to noise, you should also look for rust on the bearing cap seals. In extreme cases, your car can even shudder when accelerating.
Vibration while driving can be an early warning sign of a driveshaft failure. Vibration can be due to worn bushings, stuck sliding yokes, or even springs or bent yokes. Excessive torque can be caused by a worn center bearing or a damaged U-joint. The vehicle may make unusual noises in the chassis system.
If you notice these signs, it’s time to take your car to a mechanic. You should check regularly, especially heavy vehicles. If you’re not sure what’s causing the noise, check your car’s transmission, engine, and rear differential. If you suspect that a driveshaft needs to be replaced, a certified mechanic can replace the driveshaft in your car.
Drive shaft type
Driveshafts are used in many different types of vehicles. These include four-wheel drive, front-engine rear-wheel drive, motorcycles and boats. Each type of drive shaft has its own purpose. Below is an overview of the 3 most common types of drive shafts:
The driveshaft is a circular, elongated shaft that transmits torque from the engine to the wheels. Drive shafts often contain many joints to compensate for changes in length or angle. Some drive shafts also include connecting shafts and internal constant velocity joints. Some also include torsional dampers, spline joints, and even prismatic joints. The most important thing about the driveshaft is that it plays a vital role in transmitting torque from the engine to the wheels.
The drive shaft needs to be both light and strong to move torque. While steel is the most commonly used material for automotive driveshafts, other materials such as aluminum, composites, and carbon fiber are also commonly used. It all depends on the purpose and size of the vehicle. Precision Manufacturing is a good source for OEM products and OEM driveshafts. So when you’re looking for a new driveshaft, keep these factors in mind when buying.
Cardan joints are another common drive shaft. A universal joint, also known as a U-joint, is a flexible coupling that allows 1 shaft to drive the other at an angle. This type of drive shaft allows power to be transmitted while the angle of the other shaft is constantly changing. While a gimbal is a good option, it’s not a perfect solution for all applications.
CZPT, Inc. has state-of-the-art machinery to service all types of drive shafts, from small cars to race cars. They serve a variety of needs, including racing, industry and agriculture. Whether you need a new drive shaft or a simple adjustment, the staff at CZPT can meet all your needs. You’ll be back on the road soon!
U-joint
If your car yoke or u-joint shows signs of wear, it’s time to replace them. The easiest way to replace them is to follow the steps below. Use a large flathead screwdriver to test. If you feel any movement, the U-joint is faulty. Also, inspect the bearing caps for damage or rust. If you can’t find the u-joint wrench, try checking with a flashlight.
When inspecting U-joints, make sure they are properly lubricated and lubricated. If the joint is dry or poorly lubricated, it can quickly fail and cause your car to squeak while driving. Another sign that a joint is about to fail is a sudden, excessive whine. Check your u-joints every year or so to make sure they are in proper working order.
Whether your u-joint is sealed or lubricated will depend on the make and model of your vehicle. When your vehicle is off-road, you need to install lubricable U-joints for durability and longevity. A new driveshaft or derailleur will cost more than a U-joint. Also, if you don’t have a good understanding of how to replace them, you may need to do some transmission work on your vehicle.
When replacing the U-joint on the drive shaft, be sure to choose an OEM replacement whenever possible. While you can easily repair or replace the original head, if the u-joint is not lubricated, you may need to replace it. A damaged gimbal joint can cause problems with your car’s transmission or other critical components. Replacing your car’s U-joint early can ensure its long-term performance.
Another option is to use 2 CV joints on the drive shaft. Using multiple CV joints on the drive shaft helps you in situations where alignment is difficult or operating angles do not match. This type of driveshaft joint is more expensive and complex than a U-joint. The disadvantages of using multiple CV joints are additional length, weight, and reduced operating angle. There are many reasons to use a U-joint on a drive shaft.
maintenance interval
Checking U-joints and slip joints is a critical part of routine maintenance. Most vehicles are equipped with lube fittings on the driveshaft slip joint, which should be checked and lubricated at every oil change. CZPT technicians are well-versed in axles and can easily identify a bad U-joint based on the sound of acceleration or shifting. If not repaired properly, the drive shaft can fall off, requiring expensive repairs.
Oil filters and oil changes are other parts of a vehicle’s mechanical system. To prevent rust, the oil in these parts must be replaced. The same goes for transmission. Your vehicle’s driveshaft should be inspected at least every 60,000 miles. The vehicle’s transmission and clutch should also be checked for wear. Other components that should be checked include PCV valves, oil lines and connections, spark plugs, tire bearings, steering gearboxes and brakes.
If your vehicle has a manual transmission, it is best to have it serviced by CZPT’s East Lexington experts. These services should be performed every 2 to 4 years or every 24,000 miles. For best results, refer to the owner’s manual for recommended maintenance intervals. CZPT technicians are experienced in axles and differentials. Regular maintenance of your drivetrain will keep it in good working order.
